Hallowed Halloween Tips

[Misdemonar]

Tip #1
Cheap skulls + Latex + Cotton Balls + Paintbrush + Shoepolish =Easy to do corpsed skull.

Gather those materials, and put on some gloves, it's going to get
messy take the skull and dip the paintbrush into the latex and cover the skull, then take a piece of cotton, and stretch it out, place that cotton onto the skull, repeat until the skull is covered, only leaving some bald spots. Then, take the paintbrush once again, and cover the cotton in latex, thick enough that it does not look like an adorable teddy bear skull. Wait for the cotton to dry, then uncap the shoepolish and paint the entire skull with it. You're finished and have something gruesome for halloween.

Also, you might want to stretch the cotton over the eyesockets or open the jaw and strech a piece over that.

[Dr. V]

I like that

[Misdemonar]

Not sarcasticly I hope.

[Dr. V]

No, I really like it. See?



Got any more hot tips?

[Misdemonar]

Tip # 2
Blucky skeleton, Blucky = 8 dollar skeletons, they are blow molded,

You can corpse these in the same manner like the skulls, just replace the skull with another more corpsed skull, and if you can replace the hands and feet. (I haven't tried this, just cut out the spaces between the ribs on the ribcage to make a more realistic one, if it messes up your blucky, sorry )

[Dr. V]

This place has fantastic skeles and skulls.
http://anatomical.com/Bcategory.asp?c=7&sid=w5x975wd

[Fathom Zero]

Misdemonar, this is the best thing you've done ever.

[Misdemonar]

Tip # 4
Molding your own skull,
This is reliteviely new to me, so we both will be doing this, take a tub big enouth to fit two halfs of the skull in, fill it with baking soda, then add water, now, take your skull and and tip each half into the baking soda, after that take some insulation foam and fill each half, wait for it to dry. Now that it's dry take it out of the baking soda and clean it off, also carve the back end so that you may hot glue it together. Carve the back end so that it many be flat, and then take a hot glue gun and put it together. (Donot used corsped skulls in this process)


Tip # 5
Look around monster
One of the oldest props ever, is taking a fan that roatats, and taking of the blades and cage, and sticking a foam head onto it and then putting a mask onto the foam head, and then using pipe build a dummy on it.

[RaNkeri]

pix pls

[Sethomas]

Mold my own skull? What if I can't hold my breath while the plaster dries?

[Misdemonar]

I don't know, put flowers pedals on your penis and hide in the bushes?

[Misdemonar]

Tip # 6
Greatstuff = intestines,
Take a can of great stuff, and find a cardboard board, then spray the greatstuff in a intestinal pateren, after that dries, paint it pink, then use red paint to add blood.(can also be added to a shirt to make a shitty halloween costume.)

[Mockery]

Great tips so far Misdemonar :o

[Dr. V]

What the hell is greatstuff?

[Misdemonar]

Spray insulation foam.

[Misdemonar]

Tip # 7
Make-up appliance
Raw latex my look toxic, that's because it is, but you can put some onto your face, just don't lick it, and then, when it's dry, just rip at it with your hands, then add red food coloring.

[Dr. V]

I got some, since you mentioned liquid latex.

Puff out your cheeks as much as you can then apply latex to them. keep your cheeks puffed untill it drys and release. Instant wrinkles.

This one's cool, apply a layer of LL and then put a piece of single ply tissue or toilet paper on it and let it stick. Tear off the excess and apply another layer of LL. (you may want to apply 2 or 3 more layers to get a good thickness.) After all that dries, find some cheap makeup that matches your skin and apply it to the latex, and set it all with some colorless powder (3.99 for a little jar at your local halloween joint) Now you can do whatever you want with it, tear it, cut it, or my favorite, get a medical syringe, fill it with fake blood and CAREFULLY slip it under the appliance. Then release the blood and seal off the part you lifted. Vola, a giant blood blister you can burst in people's faces!

[Misdemonar]

Ow, you beat the hell outta me.
Thanks for the compilment rog.

Tip # 8
Appliances
Take a skull, and put it in a vice, I like to use the ones with a more flatter face, get some liquid latex, and a brush and spread it around the area of the skull that you would want to put on your face, do this for about 5 layers or so,(also make shure this skull is big enougth to have a reasonbly sizeable appilance to your face) let it dry, then peel it off, slowy, you could paint it, but I just throw blood all over it. Take some spirit gum and apply it to your face.

[Misdemonar]

Tip # 9
Distressing Clothes
Take a suit or somthing from the thrift store that you like, then, in a dirty part of your backyard, dig a hole for those clothes to fit into, spray the suit with water, and throw the clothes into the hole and bury them. Wait a week or two and come back, and see what horrors you have done!

[Misdemonar]

Tip # 10
Buckets of gore
Get an old bucket, and spray foam, put some gloves on, then put paper towls ontop of the bucket, tape the sides down, then spray some foam onto the towels, makeing some nice gore. Then take some fake arms and press them into the gore. Wait for it to dry, and then take a red spray paint, and spray it red, leaving some of the arms regular, then spray alot on the sides so it drips.

[Grislygus]

I wouldn't use spray paint. You can usually cook up a nice, sticky, dark red conglomeration on your own, using various substances.

[Misdemonar]

Make it look wet with clear finish, and good luck painting it with a brush. And I swear to god if someone posts Finish = High, I will choke them!

[DuFresne]

Finish = High

You were saying?

[Misdemonar]

Welcome to I-chockery, bitch!

[Dr. V]

The thing I liek to do which I did here...




is take the layer of latex and kinda rip it in the middle and form that popped bubble like opening and use Cinema Secrets' injury stack as a base, then just swab soem blood on it.